Parts & Accessories

You know that feeling when you're just rippin' along and you hear the dreaded psssssssssssss sound from your tire? Well have no fear the TCS Tire Plug kit is here. It's easy to use and will get you back on two wheels in no time. More time for miles of smiles, rather than expletives on the side of the road or trail. Yea, we have all been there. The TCS Tire Plug Kit uses durable "Rocket" anchors (because they look like tiny rockets) that stay in your tire and hold the plug in place. You will not lose a plug. The anchor will hold it in place like a ship at dock. But wait... there's more... You can reuse the anchors when you're all done. It's like a treasure chest when you need to swap-out your tires. The Rocket Plug Kit also features an 'Extra Hand' tool under the smaller cap. If you haven't pre-loaded the Rocket, the Extra Hand will temporarily plug the hole and take the pressure off while you prepare your Rockets and plugs. We went through a lot of arguments at WTB to get this thing dialed and man, we are so stoked on how it turned out. We hope you like it as much as we do. REUSABLE "ROCKET" ANCHORS Rocket anchors rotate once pushed into the tire and physically prevent the plug from pulling back through the tire when running higher pressure or through heavy cornering like traditional plugs can. Oh, we tried to pull it through, and we were holding up e-bikes from the plug. The anchor remains fixed in place until it’s removed from the inside of the tire and put back in the tool for future use. Reusable and Recyclable! Win, win! EXTRA HAND The Extra Hand (because who couldn't use an extra hand every once and a while) stopper can be pushed into the puncture to temporarily stop any loss of air while a rider determines how many tire plugs are needed and prepares to seal it. The Extra Hand can also be used as a reamer to create a more uniform hole for the tire plugs to seal. COMPACT AND LIGHT The TCS Rocket Tire Plug Kit is CNC’d from 6061 aluminum alloy with an integrated extra hand tool and plunger. It also has internal storage for four anchors (two large and two small included), and fifteen 1.5mm diameter tire plugs. Ready to Launch Rocket anchors can be preloaded with 1-4 tire plugs depending on the terrain and size of punctures riders typically encounter. Preloaded Rocket anchors are then placed on the plunger, ready to launch the moment a puncture occurs. The clock is ticking! TCS Tubeless TCS (Tubeless Compatible System) is WTB's standardized tubeless system. When you do get a puncture with a tubeless tire with sealant inside, this is a great way to fix it.

- For square taper and flanged. - Fits most cartridge BBs - Shell: 8mm Flanged axle bolt

- Shell: 8mm flanged axle nut - Flanged

Replacement Axle nuts for three speed Sturmey Archer hubs.

Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3

Convert Roval wheels with 142 or 142+ to be used with Boost spacing (110 /148mm) suspension forks and frames. - Kits include front and rear hub end caps, rotor spacers, and kit specific rotor bolts - Compatible with select MY13-16 Roval Wheels. Choose the appropriate SKU for each wheelset - Each conversion kit requires the existing rear wheel to be re-dished to center. Consult an authorized dealer to perform this operation

Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

The Problem Solvers Axle Nut is perfect for wheels with solid axles (also called bolt-on axles). This quality nut is made of durable chrome-plated steel and features a built-in integrated rotating washer to hold tight.

- Flanged 15mm axle nuts - Durable chromoly construction - Spacing / Axle: B/O

Origin-8's Track Cog Lock Ring with left-handed threading and 1.29 x 24tpi in a chrome finish completes your basic track cog locking needs.

- High-quality fat bike rim strips - Super durable PVC material

The Muc-Off Tubeless Rim tape is made from their proprietary performance material with a pressure-sensitive adhesive to provide just the right amount stretch whilst maintaining durability and strength needed to create a lasting airtight seal. Semi-transparent material makes locating the valve hole easy.

Bearings for maintaining and rebuilding DT Swiss hubs. - DT Swiss 1526 Bearing for Rear Driveside Spline 1200, 2nd Generation Spline1501 and Dicut Disc Wheels

Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.

- ProLock: pre-prepped/treated nipple threads with special compound - Hexhead (14g only) design for building/truing at nipple head, in addition to 4-sided flats at rim protrusion - Form-A design assures smooth fit and build - Cold-forged nipple blank machined to DIN 79012 specs - 14mm overall length (2mm taller hexhead for wrench interface, but protrusion through rim is the same as a 12mm DT nipple) - 2.0mm (14g) spoke thread interface with full run-through - Made in Switzerland. - Box/100

Ease of use, lightweight, and optimum performance in a single product. The DT Pro Head shape, combined with both a torx and a square tool interface, makes wheel building a lot easier. The spherical contact surface aligns the nipple perfectly with the spoke. All-brass nipples are recommended for e-bike use. Weight: starting at 26g for 64 nipples.

The buyer's choice for wheel builders looking to save weight. The nipples are available with or without DT Pro Lock, a patented liquid inside the nipple thread that makes the connection between the nipple and spoke extremely durable. It pairs perfectly with any wheel, though all-brass nipples are recommended for e-bike use. - Weight: starting at 20g for 64 nipples